Energy storage and power conversion system test solution

Energy storage inverter (PCS) for the connection between the battery and the power grid can realize power bidirectional conversion device, on the basis of Chroma 8000 ATS customization system, specifically for energy storage inverter for automated test validation, collocation of Chroma of 61800, 62000 d, 17040 two-way series products such as network/battery simulator and measurement equipment, complete for energy storage inverter PCS interconnection test, PCS performance testing, PCS output input test, PCS protection test and pv characteristic test.

• 2 in 1 bidirectional dc power + feedback load
• Voltage output range: 0-1800 - v, current 540 a, power of 540 kw
• Pv, battery, fuel cell simulation

• Operation modes: constant current/constant voltage output
• Channel power of 25 w voltage 5 v (series), channel, channel current 5 a (parallel)
• Two-way power supply design (analog charging/discharging status)
• Section can be simulated 480 battery series battery core power (240 batteries in series and two batteries in parallel)

• Multi-channel battery module state simulation
• Based on battery core behavior, battery status simulation
• Can be set battery commonly used parameters and rapid custom output initial state
• Rechargeable battery charge and discharge current switch don't interrupt, simulation can discharge characteristic, used for two-way application components

• For the battery module production or research and development unit test validation use
• This automated test system can improve the efficiency of product quality by more than 80%
• Withstand voltage test battery module function of BMS/joint/consistency/performance
• Charge and discharge power range: 5 kw to 350 kw
• Charge and discharge voltage/current range: 0 v ~ 900 v / 0 a ~ 1000 a

• Voltage 20 v, 60 v, 100 v, 200 v, 500 v power battery, battery storage test
• Up to 60 independent channels, and current application of the general assembly

• Operating modes: constant current/constant voltage/constant power discharge
• Channel power 10 kw, 20 kw (80 kw) can be parallel to the
• Channel voltage 60 v, 100 v, 200 v
• Channel current 180 a / 100 a (800 a) can be parallel to the

• Voltage range: 60 ~ 1000 v, current range: 0 ~ 750 a, power range: 0 ~ 300 kw
• Current/voltage measurement accuracy (plus or minus 0.05% FS/plus or minus 0.02% FS)
• Voltage/current file an automatic switching function
• Can meet the international standards of power battery test: IEC, ISO, UL, GB/T, etc
• The battery discharge energy recycle function (Eff) > 90%, PF > 0.95, I_THD < 5%)

• High power testing equipment of up to 1700 v / 4800 a / 1.2 MW
• Multiple security protection, meet the battery test personnel safety risk controls
• Flexible integration technology, the automatic battery test solution

• With fault injection function simulation, helping to improve the function of the ISO 26262 security testing
• Up to 1200 v / 600 a battery analog voltage and current, the actual verification calibration parameters such as the SOC of the battery management system, SOH
• Test battery management system in static or dynamic situation of overvoltage (OVP) (UVP), low voltage, over current (OCP) composition among (OTP), temperature or low temperature (UTP), and other protection
• Support the CAN, CAN FD, LIN communication interface...

• Scope: power 1800 w, 3600 w, 4500 w
• Parallel/three-phase control (AC mode only)
• Ac load: general load and rectifier load mode
• Dc load: constant current, constant resistance and constant voltage, constant power mode

• 2 in 1 bidirectional dc power + feedback load
• Voltage output range: 0-1800 - v, current 540 a, power of 540 kw
• Pv, battery, fuel cell simulation

• Output power: 9 kva ~ 15 kva
• Output voltage: 0 ~ 350 v
• Height of 3 u have the design of high power density maximum of 15 kva
• Touch panel collocation completely intuitive UI design

• New high voltage 1800 v group of tandem pv inverter test scheme
• Scope: power 2 kw / 5 kw, 10 kw / 18 kw, 15 kw/maximum power can be up to 1 mw
• High speed response on the I - V analog
• Built-in standard EN50530 / Sandia/CGC - GF004 / CGC - GF035 / NB - T32004 dynamic MPPT test project

• Output power: 30 kva ~ 300 kva
• Output voltage: 0 ~ 300 v, 400 v (to buy)
• All four quadrant energy recovery function
• The simulation waveform distortion electric capacity

• Stand-alone built-in high voltage withstand voltage test and the PD detection function
• Programmable ac voltage is 0.1 kVac ~ 10 kVac
• High precision and high resolution ammeter 0.01 uA ~ 300 uA
• Partial discharge (PD) detection range 1 PCS to 2000 PCS

• 5-in-1 safety comprehensive Test (ACV/DCV listed/GB/LC/IR Test)
• Can program output voltage 5 kv AC, DC 6 kv
• 500 va output
• Grounding connection (40 a)

• Withstand voltage test: communication 5 kv / 100 ma;Dc 6 kv / 25 ma
• Insulation resistance testing: 5 kvmax;1 m Ω Ω ~ 50 g

• The Open architecture software
• Expandable hardware